Shooting Sports > Archery
Longbow Build along (Page 1) (Part 1-8)
Rancid Crabtree:
I am going to show the steps in making this bow for my son. I am not an expert by any stretch. This will be a build along sort of thread but I must warn you that this will be slow going. I have many projects in the works with much stricter time lines than finishing this bow for my son so there will be periods of inactivity. Thats just real life.
This bow will be a reflex/deflex Long bow. It is a hybrid combination of a longbow and a recurve. Longbows are typically straight when unstrung and recurves are still curved even when unstrung. This bow will look sort of like a recurve while unstrung and like a longbows when strung.
Here is a pic I stole off the web to give you an idea of what I am going for.
The woods I am using for Josh's bow are the same ones I use to make knife handles. For the most part, they are South American hardwoods. The riser will be made from Bubinga, Bloodwood and good old American hard rock maple from a tree my Dad cut many years ago. Sort of a legacy piece of wood, cut by my Dad, Made into a bow by me and finally used by my son. I will also use some of the Maple in the limbs.
this is the order in which I will stack the layers.
Most S.A. hardwoods have oils in them that make gluing difficult, so I use acetone to clean and degrease. Blood wood and purple hear are some of the oiliest. You can see the orange oil in the basin of the sink. It took a long time to clean that sink. I should have sprayed it with pam first. :oops:
Once cleaned, I used a hacksaw blade as a scrapper to rough up all the gluing surfaces. Epoxy does not like smooth surfaces.
The glue I am using can be purchased at a number of bow building web sites. This is a two part epoxy that gets stronger if cured under a heated condition. This is important because if you leave the bow in a hot car on a sunny day, The glue had better have been cured at a high temp to keep the bow from de-laminating.
It mixes like any other epoxy.
Make sure to cover your work surfaces with wax paper or plastic wrap. It is hard to clean up any spills. Then simply butter both sides of the surfaces to make sure you have no dry spots that will later separate.
I use spring clamps because C-clams will get loose during the heating process when the glue oozes out. (trust me, there is a lot of oozing) :( Spring clamps keep a constant pressure at all times.
I then take the riser and put it in a preheated oven. Bake for 8 hours at 180F until a nice golden brown and serve with a scoop of vanilla ice cream . ::)
When it comes time to glue up the bow itself, I will build an oven box that is 6 feet long as the bow will not fit in the oven. I will heat this box with 100 watt light bulbs.
Fast forward 8 hours and a few more hours for a slow cool down period and the riser is all glued up. The rubber tips of the clamps need to be pried from the glue.
Next, I ran the block through my table saw to square it up and remove the excess glue.
Then I drew the riser pattern on the wood and cut it out with a band saw and sanded the fade outs on a drum sander.
This glue is a flexible epoxy. Normal hardware store epoxy would crack and break if bent like this.
Make sure to use only enough glue for the job at hand. A little goes a long way.
I now need to make the form that I will use to glue the bow on and I need to make the heat box. Like I said, this is going to be a slow moving project. I will post more progress as I get a chance to work on it.
Rancid Crabtree:
Before I can go any farther with Josh's bow, I need to build the form that the bow will be glued together on. There are a lot of ways to go about this and forms can be made many ways but I chose a way that seemed easy to me.
I bought a nice straight 2 x 10 and traced the form that I came up with onto the wood.
Then cut it out with a jig saw.
I then went over the entire length of the curve with a square to make sure there were no twists in the form. Any irregularities were taken out by sanding.
In order to keep the form straight over time and in the heat of the oven box, I screwed a few 2x4's along both sides. They will also act as feet to keep the form from tipping over. Next, I covered the entire curve with a piece of 1/8th inch thick by 1 1/2 wide aluminum strip. This will make the the curve a much better surface to build the laminations on and it will be more repeatable should I want to build more bows from this form. This form will build bows up to 70 inches in length. This bow will be a 66 inch model.
I need to drill a bunch of clamp holes along the curve for the spring clamps but that will have to wait for another day.
Rancid Crabtree:
I spent some time today, making the clamp holes in the form. When I assemble the bow, I plan to use spring clamps to compress all the layers of wood, fiberglass and epoxy together.
I drilled big round holes and then used a jig saw to square up the side of the hole closest to the top surface. This will give the clamps a little more room.
I will use one clamp on each side of the limb. Like this.
I also got a package in the mail today from Old Master Crafter of Waukegan, IL. I ordered the wood laminations a few days ago and these things showed up a lot faster than I was told they would. (Great Service) It does not look like much for about $60 but what it is, is 6 taper ground action wood strips that are .065" thin on one end that taper at .001" per inch of length. The strips are 36 inches long and 1 1/2 inches wide. they came protected by two nice looking strips of Zebra wood. I will use them for knife handles at a later date.
I placed the thick end of one piece next to the thin end of another so you can see the taper.
Each limb will get three of these tapers and one strip of parallel thickness Hard rock Maple that is from the piece of wood my Father cut so many years ago. This is the same piece of wood that I used in the riser.
On the front and back of each limb will be a thin layer of Kingwood and then clear fiberglass. All of this will be assembled with the same epoxy I used to make the riser but first I need to assemble an oven box.
Rancid Crabtree:
On Sat. Morning, I built the oven box for the bow form. I will spare you the details since it's just a box made from scrap plywood that was left over from another project. I will say that It is 12 inches high and 22 inches wide and 74 inches long. By removing 6 screws at each end of the box, I can reduce the box to four individual panels for easy storage.
You will also notice that the box has neither a top or bottom. The reason for not having a bottom is so that I can bring the box to the form that will be covered in oozing epoxy and many clamps (creating a challenge to move) I would rather bring the box to the form.
With the box complete, I assembled the heat source that I will use to raise the inside temp of the box to 160F. A trip to the Home Depot for the supplies ran me about $30.
The first step was to get rid of those pesky warning labels. Nobody reads them any way. The extension cord company knows I am not going to read the label in English so why would they expect me to read it in Spanish? I hope the extension cord labels are not like mattress labels. I would have to spend time behind bars for removing them.
Once I cut the extension cord into bits, I wired the light bulb bases together in series so that one plug would power them all.
A quick test revealed that I had had paid attention in shop class.
I placed the form between the two light bulb boards and brought the box to the form. My Son will need to help with this part as the box is a bit long to handle alone. Everything fits nicely.
The cover of the box will be an old closet door from our last house. It is hollow so it is light enough to move around and it was free.
I drilled a hole in the door and inserted the probe of a thermometer. This way, I can keep tabs on the temp inside the box without opening it and letting the heat escape. My wife won't be cooking a turkey for a few months anyway.
After two hours with the bulbs on, the temp never got above 135F. I will replace the 100 watt bulbs with 150 watt bulbs and add two additional bulbs to the boards
[/quote]
The next test will include covering the oven box with a canvas to trap the heat better. I think 2 extra bulbs should do the trick.
The next sep will be to make a test bow out of scrap material so I get the feel for the assembly process and so that I can check the glued up trial piece for any warps that I will be able to correct before wrecking a bunch of expensive woods and fiberglass. It is a piece of mind exercise.
Rancid Crabtree:
In order to evaluate the bow form, I built a mock up. I bought a pine, 2 x 6 and cut it into strips that were .065 thick.
Before gluing the strips together, I protected the form with two layers of tape. It will be easier to remove and replace the tape then it will be to try and chip away any excess glue from the form.
Next, I covered the surfaces of the form with plastic wrap to keep it clean.
I used yellow wood glue for the mock up. It did not require the oven box. Once all the layers were covered in glue, I used clamps and strips of rubber inner tube to compress the layers.
In the center section (where the riser will be) I added a few extra strips.
After 24 hours, I removed the clamps and the plastic wrap. There was no "Spring back" or relaxing of the wood strips. I then took the mock up and reversed it on the form to see if it was symmetrical and it fit the form equally in either orientation.
I checked for twists in the limbs and found none.
I then placed the riser against my chest and grabbed both limb tips and began to flex the bow. Since I did not have any fade outs and the ridged glue does not like to flex (and the pine had many knots) both limbs broke
This allowed me to nest the limbs and look for any twists or differences between the two. Everything looked good.
I think all is ready to assemble Josh's bow. Now I just need to find the time to actually do it. Since I will want to baby sit the oven box for the 8 hours that it will cook, It's going to have to wait until I have a free weekend and those are hard to come by.
Navigation
[0] Message Index
[#] Next page
Go to full version