Author Topic: The "Hunting gear" storage shed project  (Read 9546 times)

0 Members and 1 Guest are viewing this topic.

Offline Rancid Crabtree

  • Sr. Member
  • ****
  • Posts: 389
  • Karma: 1
  • Happy to be here
    • View Profile
The "Hunting gear" storage shed project
« on: July 06, 2016, 08:50:28 AM »
Now that we are back from our 4th of July trip it?s time to start a storage shed project that been on the back burner for a while. My son and I are building the shed. Its time to take the garage back which has become the manufacturing area for Innovative Outdoorsman products and we need a better storage area for all the ladder and chain on tree stands and climbing sticks and deer decoys and other hunting gear and yard tools. We designed the shed and gathered all the supplies before the holiday. Its going to be a 12 x 12 shed with a roofed overhang on one side. The shed will have 8 foot walls and a couple windows. It will have double doors, a ramp for the riding mower and a roof vent because sheds can get pretty hot inside. The plan is to work on the shed in the afternoon/evenings after work each day as weather allows. I?ll use this space to detail the project as we make progress. Here is a drawing of the shed we designed and used to generate the bill of materials.

Any day in the woods is a good day.

Offline Rancid Crabtree

  • Sr. Member
  • ****
  • Posts: 389
  • Karma: 1
  • Happy to be here
    • View Profile
Re: The "Hunting gear" storage shed project
« Reply #1 on: July 08, 2016, 05:42:02 AM »
I dug away the topsoil and backfilled with crushed paver base and tamped it down and leveled all the pavers. Then the treated 4 x 4?s were laid on the pavers and the floor joists on top of that. The sun went away and the mosquitos came out in full force but it?s a good start.






Any day in the woods is a good day.

Offline Rancid Crabtree

  • Sr. Member
  • ****
  • Posts: 389
  • Karma: 1
  • Happy to be here
    • View Profile
Re: The "Hunting gear" storage shed project
« Reply #2 on: July 09, 2016, 08:45:36 AM »
The next step is nailing in all the floor joist braces which provide support/spacing and nailing for the floor decking. The floor is ? plywood with tongue and groove edging to lock it all together. The big flat deck is the perfect place to build the trusses needed for the roof. There was still daylight so I built a jig for the 7 trusses and had time to build the first truss. 6 more to go but that?s for another day as I?m out of light.






Any day in the woods is a good day.

Offline Rancid Crabtree

  • Sr. Member
  • ****
  • Posts: 389
  • Karma: 1
  • Happy to be here
    • View Profile
Re: The "Hunting gear" storage shed project
« Reply #3 on: July 11, 2016, 05:42:31 AM »
All 7 trusses are finished and will be set aside waiting for the walls to go up.



Then it was time to build and raise the walls




Any day in the woods is a good day.

Offline Rancid Crabtree

  • Sr. Member
  • ****
  • Posts: 389
  • Karma: 1
  • Happy to be here
    • View Profile
Re: The "Hunting gear" storage shed project
« Reply #4 on: July 12, 2016, 05:22:02 AM »
Because the roofed overhang on the west side will make it challenging to raise the fiber/cement siding, we installed those 3 sheets before raising the trusses. The Fiber Cement siding sheets are heavy (80 Lbs each).





Then we were good to go raising the 7 trusses. That used up the rest of the daylight. We still need to brace all the trusses but that is for another day.






Any day in the woods is a good day.

Offline Rancid Crabtree

  • Sr. Member
  • ****
  • Posts: 389
  • Karma: 1
  • Happy to be here
    • View Profile
Re: The "Hunting gear" storage shed project
« Reply #5 on: July 13, 2016, 05:39:30 AM »
All the trusses are braced and reinforced.





In order to work safe while installing the roof decking and later shingling, we built a temporary scaffolding. (Ladders suck) Then it was time to trim the truss tails and install sub facia. Having scaffolding helps in doing a straight and square job that shows up when viewed from the ground.






Any day in the woods is a good day.

Offline Rancid Crabtree

  • Sr. Member
  • ****
  • Posts: 389
  • Karma: 1
  • Happy to be here
    • View Profile
Re: The "Hunting gear" storage shed project
« Reply #6 on: July 14, 2016, 05:42:42 AM »
Time to raise most (but not all) of the roof sheeting (1/2? OSB) 4 Full sheets and 4 half sheets were nailed in place. The two sheets at the bottom of the overhung ?lean to? portion of the roof were not installed so that the 3 support posts and header could be installed. (They needed to be raised above the roof line in order to be dropped down into the holes that were dug)



The last sheets of roofing we not installed with the rest so there would be room to raise the 3 treated 4 x 4?s and their header to support the roofed overhang. Holes were dug (Through mostly rocky ground with some clay soil around them. This dirt really sucks for digging) Since there is not enough suitable soil to put back in the hole the support post holes are backfilled with paver base and tamped and settled with water. Then all three posts all were trimmed to the same height and the 4 x 4 header beam raised and installed. All the truss tails were then nailed to the header beam and trimmed and the sub facia installed. Then the last sheets of roof decking installed.






Any day in the woods is a good day.

Offline Rancid Crabtree

  • Sr. Member
  • ****
  • Posts: 389
  • Karma: 1
  • Happy to be here
    • View Profile
Re: The "Hunting gear" storage shed project
« Reply #7 on: July 15, 2016, 07:42:40 AM »
Before we can shingle we have to install the metal drip edge. Before the metal drip edge is the final trim, before the final trim is the facia and soffit trim and none of that can be installed until more siding is installed so that where we focused our efforts next. Aside from hot dip galvanized nails, the sheets of fiber cement siding are also attached with construction adhesive. Then the first trim boards were installed along the roof line and all the seams between the sheets of cement board siding were caulked. While we were in trim mode we added some of the vert. corner trim and final roof edge trim pieces. Then all the trim was given two coats of exterior paint.






Any day in the woods is a good day.

Offline Rancid Crabtree

  • Sr. Member
  • ****
  • Posts: 389
  • Karma: 1
  • Happy to be here
    • View Profile
Re: The "Hunting gear" storage shed project
« Reply #8 on: July 18, 2016, 05:46:42 AM »
The metal drip edge is installed which means we are ready to start shingling the roof.



We look forward to the weekends because it affords a lot of time to work on the shed. The weather doesn?t care so we suffered a rain delay.



We looked out the window and saw the local inspector checking out the progress.



When everything dried up we build more temporary scaffolding so we can safely work on the roofing.





The hole in the roof for the vent.



The back side is complete.



Nice straight lines.

Any day in the woods is a good day.

Offline Rancid Crabtree

  • Sr. Member
  • ****
  • Posts: 389
  • Karma: 1
  • Happy to be here
    • View Profile
Re: The "Hunting gear" storage shed project
« Reply #9 on: July 19, 2016, 05:40:56 AM »
With the exception of the ridge cap, the front side of the roof is complete as the sun sets on another day.



The ridge cap is added the next morning and completes the roofing job.



Now that the roofing is complete the scaffolding is removed so the final wall can be closed in. The windows are the first thing to go in.





Then the last sheets of cement siding.



It?s starting to look like a shed now.
Any day in the woods is a good day.

Offline Rancid Crabtree

  • Sr. Member
  • ****
  • Posts: 389
  • Karma: 1
  • Happy to be here
    • View Profile
Re: The "Hunting gear" storage shed project
« Reply #10 on: July 20, 2016, 05:23:18 AM »
The fiber cement siding is very heavy which means the doors need to be stout so they won?t sag over time. The door framing is finished.



Tight joints, construction adhesive and long decking screws should keep the doors from sagging as time goes by.



To make the doors really strong and to tie it all together, the fiber cement siding is attached to the frames with construction adhesive and nails. The door frames are spaced and shimmed and held in place with big clamps so the siding can be added right in place to better control gaps and clearances.



The clean up crew grabbed the camera while we added the cement siding to one of the doors.



Then the entire door is removed and painted before the trim and hinges are added. The trim is painted too.




Any day in the woods is a good day.

Offline Rancid Crabtree

  • Sr. Member
  • ****
  • Posts: 389
  • Karma: 1
  • Happy to be here
    • View Profile
Re: The "Hunting gear" storage shed project
« Reply #11 on: July 21, 2016, 05:24:47 AM »
When the paint dried the Heavy duty hinges are added and the doors hung. Each door weighs about 90 Lbs.







Lastly, all the trim is added and caulked and painted again.




Any day in the woods is a good day.

Offline Rancid Crabtree

  • Sr. Member
  • ****
  • Posts: 389
  • Karma: 1
  • Happy to be here
    • View Profile
Re: The "Hunting gear" storage shed project
« Reply #12 on: July 21, 2016, 06:58:06 AM »
While inside the shed, we heard a cluck. We looked outside and then grabbed the camera when we saw the building inspectors show up.

https://www.youtube.com/watch?v=gn6zbJLRWBE
Any day in the woods is a good day.

Offline Rancid Crabtree

  • Sr. Member
  • ****
  • Posts: 389
  • Karma: 1
  • Happy to be here
    • View Profile
Re: The "Hunting gear" storage shed project
« Reply #13 on: July 22, 2016, 05:24:59 AM »
Before the big storm hit, the windows got trimmed.



And we closed in the short side eaves to keep out the birds, bats and bees. Vents were included and the last pieces of corner trim were added.


Any day in the woods is a good day.

Offline Rancid Crabtree

  • Sr. Member
  • ****
  • Posts: 389
  • Karma: 1
  • Happy to be here
    • View Profile
Re: The "Hunting gear" storage shed project
« Reply #14 on: July 25, 2016, 05:41:37 AM »
Spent the weekend up north so not much shed work was done. Did however manage to work on the ramp. The ramp is made from a 8 ft, 2 x 12 that is cut in half and then the two halves cut diagonally to create 4 tapered ramp stringers. The 4 stringers were screwed to the shed floor so everything would be square and flat and then treated decking was screwed to the top.







The ground is leveled and the ramp is attached to the shed with 4 inch deck screws.






Any day in the woods is a good day.

 

Google
Web http://www.wisconsinoutdoor.com